Home > Motors & Gearings > Motor / Gearing Tuned Systems > Power Wheels Arctic Cat Tuned Kits >

Stage V D.I.Y. Super Speed Motors/Gears
Stage V D.I.Y. Super Speed Motors/Gears


 
Alternative Views:


: $225.00
: $195.00
Savings: $30.00


Product Code: STAGE-V-DIY


Heatsinks?:


Installation Aids:


Qty:  
Description
 
This kit will work on any Power Wheels 7R Gearbox housing originally designed for 15-17 tooth motors. This includes: Arctic Cat, Dune Racer, Dune Racer Extreme, Baja Extreme, Baja Trailster, 2-seat F150, Jeep Hurricane, and Cadillac Escalade.
We've swapped the normal 72 tooth first gear for a 66 tooth Hardened Steel one running on Ball Bearings and the pinion gear is swapped to a 22 tooth Hardened Steel making this the lowest gear ratio (highest top speed) available in any ride-on. Our Performance 775 motors provide insane amounts of torque for off-road and handle up to 24 volts without a care. The thicker-then-molasses stock grease gets replaced with our Lithium Race Grease designed to coat the gears and shafts to make them more slippery and create less heat buildup. This setup is for die-hard speed addicts only. Kit includes:

- 2 massive 775 size Modified Motors with Internal Cooling Fans.
- Torque sleeves on both motors for more low-end power.
- Quick-Change Motor Wires
- 2 Hardened 22 Tooth Steel Pinion Gears with Lifetime Warranty pre-mounted*.
- 2 Hardened 66 Tooth Steel First Gears with Lifetime Warranty*.
- 4 Steel Ball Bearings.
- MLToys Lithium Race Grease for even more speed, motor durability, and more run time.
- Written and video instructions.

Motors are safe for 12-24 volts of SLA Batteries. Not for use with lithium batteries unless you use our Soft Start Low Voltage Lithium Module. You will need a drill with Phillips bit, pliers, 120-180 sandpaper, and cookies to complete the installation.

Stage V gears should only be used on-road or light gravel because of the higher speed gear ratio. No passengers or added weight. See video below on how to install gears into your gearboxes.

Just like when modifying a real car, modifying a Power Wheels voids all warranties. If you have made any non-MLToys modifications to your car you should reach out to our tech support first to check compatibility. MLToys bears no responsibility for damage to vehicle, persons, or property incurred by modifying a vehicle. Be Smart, Be Safe, and Have Fun!
Stage V Motors/Gears and 24v Conversion Kit
Stage V Jeep Wrangler 24 volts
How to Install Steel Gears

Recommended Accessories
Brake Reduction Module Cap Nut Tool Four Point Safety Harness 24 Volt Conversion for 12 Volt Power Wheels w/ charger
: $11.00

Add
: $1.00

Add
: $19.99

Add
: $152.00

Add
Brake Reduction Module Cap Nut Tool Four Point Safety Harness 24 Volt Conversion for 12 Volt Power Wheels w/ charger
Dual Motor Temperature Gauge In-Dash
: $10.00

Add
Dual Motor Temperature Gauge In-Dash

Average Rating: Average Rating: 4.5 of 5 4.5 of 5 Total Reviews: 5 Write a review »

  0 of 0 people found the following review helpful:
 
3 of 5 Easy but quick failure March 25, 2022
Reviewer: Michael Wozny from Chicago, IL United States  
The team at ML was great and all the parts were pretty easy to install. Unfortunately one of the 775 motors burnt out shortly after install. I followed the break in directions as instructed, but we only got about 20 minutes of use before it died.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 October 16, 2021
Reviewer: Rex herndon from Lewisville, TX United States  
Took longer to receive than expected
However everything else great

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 August 20, 2021
Reviewer: Leroy Marshall from Hammonton, NJ United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Satisfied August 4, 2021
Reviewer: Gary Erkenbrack from Forest Lake, MN United States  
These are great our Escalade goes really fast now

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Old gearbox still works May 24, 2021
Reviewer: Darren Griesbach from Cudahy, WI United States  
Ordered the kit but had old gearbox so gear wouldn't fit.  Modified my gearbox with some 3/8" 3"16" bearings and some 3/16 steel round rod.  Pushed out the old 3"8 peg and new gear fit old gearbox perfectly.

Was this review helpful to you?